MapForums
Community of VE/MapPoint Users and Developers
Opening a .axe in mappoint 2006
This is a discussion on Opening a .axe in mappoint 2006 within the MapPoint 2006/2009 Discussion forums, part of the Map Forums category; Does any 1 know how to open a .axe in mappoint 2006 when i try it opens an error message ...
| |||||||
| Register | Blogs | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
08-27-2007
| |||
| |||
 Opening a .axe in mappoint 2006         |
|
08-27-2007
| ||||
| ||||
| .axe file
Can you give more information on an .axe file? Do you know where it came from? Can you open it in a text editor? Thanks, Eric |
|
08-27-2007
| |||
| |||
| Re: .axe file
It's an autoroute European map file, when i open it in notepad it comes up with a load of rubish. I have autoroute 2007 and it opens ok in that the thing is that i cant export the data from it, someone sugested mappoint as there is an export feature but it wont open. |
|
08-27-2007
| ||||
| ||||
| Re: Opening a .axe in mappoint 2006
Are you using the European Maps version of MapPoint 2006 (not the North American version)? just checking. It could be because AR07 is newer than MP06... ? so you might try pasting the data from AR07 into AR06 or AR05 and then try to open from MP06EU. In AR07, are there any other options for Save As ? There are tools for reading Microsoft geography files (e.g. ptm, est) directly and exporting to text. You might try these! Read and Write Directly to MapPoint Binary Files ITNConv hope this helps! Eric |
|
08-27-2007
| |||
| |||
| Re: Opening a .axe in mappoint 2006
It's the European version, I'll try those tools and get back to you. many thnaks |
|
08-27-2007
| |||
| |||
| Re: Opening a .axe in mappoint 2006
It isn't a route I am trying to export it is a series of push pin locations about 3000 shop locations is this possible? |
|
08-27-2007
| ||||
| ||||
| Re: Opening a .axe in mappoint 2006
It should be possible... in routing or GPS terminology pushpins might be referred to as WayPoints, but they should be supported. Do you want to post your zipped axe file here? Maybe someone can get them out. I'll give it a shot. Eric |
|
09-05-2007
| |||
| |||
| Re: Opening a .axe in mappoint 2006
Sorry been on holiday, I would be most greatful if you could have a look at this for me. |
|
09-05-2007
| ||||
| ||||
| Re: Opening a .axe in mappoint 2006
I tried both ITN Conv and GPS Babel but neither of them worked... ITN Conv says there are no itineraries and GPS Babel reports unsupported version. You might try this Utilizing MapPoint for Emergency Services, MapLinx Pro, Greg Slayden, Action Engine or post to the ITN Conv or GPS Babel forums to see if someone there can help you.. Eric |
|
09-05-2007
| |||
| |||
| Re: Opening a .axe in mappoint 2006
No worries mate thanks for trying! |
 |
| ||||
| Posted By | For | Type | Date | |
| axe 2006 - Zymboo | This thread | Refback | 02-02-2008 03:06 AM | |
| Tracking P.F. Chang’s in the Midwest - MapPoint Articles - MP2K Magazine | This thread | Refback | 08-28-2007 04:28 PM | |
| Microsoft MapPoint 2006 - MP2K Magazine | This thread | Refback | 08-27-2007 11:58 AM | |
| Map Visitors - Powered by Virtual Earth | This thread | Refback | 08-27-2007 06:39 AM | |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
| Display Modes | |
Linear Mode
| |
| ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Opening VBA editor for mappoint | Brock | MapPoint 2006/2009 Discussion | 2 | 01-15-2007 08:06 AM |
| MapPoint C# Job Opening | Eric Frost | News and Announcements | 0 | 12-17-2006 08:30 AM |
| Opening a MP 2006 file in MP 2004, can it be done? | MtnDew2756 | MapPoint 2006/2009 Discussion | 4 | 08-24-2006 07:08 PM |
| MapPoint control hangs while opening a map | Anonymous | MapPoint 2006/2009 Discussion | 0 | 10-24-2002 11:18 AM |
| Opening a new map takes about 10 sec ?!?!?! | Anonymous | MapPoint 2006/2009 Discussion | 1 | 07-25-2002 12:43 PM |
All times are GMT -5. The time now is 03:42 AM.
